Showing posts with label painting. Show all posts
Showing posts with label painting. Show all posts

Monday, February 23, 2015

Playing Ketchup Episode IV: My New Hope

These last four posts get me pretty much caught up to my current status. I glossed over some of the mundane things, but tried to point out any issues I had, or solutions I came up with.

I'll go into a little more detail of some electronics things that happened later as well. I now have full Bluetooth audio up and running, but ran into another minor snag there.

Celebration Anaheim is now less than two months away and my hope is to have it all done by the time we pull away for the trip. Regardless, he's going, in whatever state he's in at that point.

I have the body mostly done aside from some touch up paint and actually attaching ankles to legs and legs to body. That's something I can't do alone at this point do to weight of everything. I'd rather wait for some help than screw anything up.

A few knick knacks here and there and I'm ready to start on my Hydro Dome. Luckily I'm happy with the finish on these new domes and don't plan on any sanding. Therefore, I just have to break all the panels off, put the Ultimate Hinges in and paint the blue portions. Is that all? :)







Playing Ketchup Episode III: Paint the Town White

During all the work I was doing on finalizing the skins for paint, I was actually painting the legs and feet. Once I had the skins ready to go I taped off the Inner Skins and painted them as well. It was a time consuming experience, and my perfectionist ideals didn't help. But I tried to chalk any chips or dings up to natural weathering.



One of the first roadblocks I came to during assembly was screwing the Center Ankle Cylinders to the Center Ankle. I apparently never tried to dry fit these before paint or I would have seen the issue. Its such a tight fit inside the ankle that its pretty much impossible to use a normal screw. After a few different attempts from advise on the forums, I came up with what worked best for me and my fingers. I used set screws placed into the cylinders first, and then screwed a nut onto the backside with a ratcheting wrench. It still wasn't easy, but I got there in the end.





Some of the easier portions of building came after. I sanded and cleaned up my foot strips and the feet area they cover before using a strong epoxy to adhere them in place.




I also painted my homemade Utility Arm bay back cover and screwed it on along with the Utility Arms and Large Data Port.




My R2 isn't based on any one particular movie, but the bits and pieces I like from each. One of those bits is the silver strip on the legs that matches the indent in the Rocket Booster Covers. My JAG version of the legs don't have this stripe CNC'd out like some other versions. I knew masking it off during painting was an option, but I was afraid that any chipping later would annoy the hell out of me. I happened to find some silver pinstripe tape in the auto department at Walmart. It's close enough to the exact size I needed that I went ahead and gave it a try. I placed the covers on the legs, marked them with a pencil and made a line all the way around with a ruler to help guide for a straight wrap around the legs. I overlapped the tape at a point where it would be underneath the covers. I'm really pleased with the result. You have to get very close to tell its pinstripe tape, and later weathering will help camouflage it even more.







I used VHB tale to adhere the skins together. It worked fairly well, but I did use some super glue in a few areas that the tape just didn't seem to work. It helped to close the gaps. I'm not sure if its because my VHB tape was a couple years old, but it did have several places that didn't adhere very well.

I'd recommend a whole lot of clamps for this too. I didn't manage to take any pics of my skins during the process, but its almost comical how many binder clips and various sized clamps I used. 



Next came getting all the various detail pieces attached to the skins. I ran into some issues with the Pocket Vents. Mine have wing tabs that are meant to help you attach them to the skins with tension alone. Problem was that they needed some heavy bending and filing to get them to fit into place. Because of my homemade Kick Panels I ended up using a dremel to put a pretty good curve into the on of the top tabs on each Pocket Vent. Just another unforeseen step in the assembly process.



I got far enough along in the assembly process to put the magnets on the back door. Clamping the door in place, I marked the inside and then used epoxy to adhere the magnets in place. Those things aren't called "Strong Earth Magnets" for nothing. It really sucks the door into place when you get it barely in position. Problem is the magnets are stronger than the epoxy and I've already had to re-adhere a few into place after they stayed on the frame magnets. I will probably have to end up using my stronger 3500 psi Gorilla Epoxy in the end.


Sunday, September 9, 2012

Double Boost

Painted the other Booster Cover today. Used the same method as before and this one came out even better.


Sunday, August 19, 2012

You so Crazy Glue

Since we were having an unusually mild August weekend, I decided to tackle painting one of the Booster Covers this weekend. This was attempt number three. The first two times the masking failed miserably and I ended up having to strip the paint off, which is not a very fun task. Learning from my previous mistakes, I altered my plan to hopefully make the third time a charm. This go round I'm doing them one at a time as well, so here was the first one.

I used good old Elmer's glue in the bottom inset channels and the two top notched out areas. I cut a thin strip of regular masking tape for the horizontal striped areas near the bottom of the covers.




I put the glue in over a series of a few hours letting it dry a little and added more until each area that needed masking was completely covered. The glue will shrink a little which I especially wanted in the four vertical channels near the bottom. Here they are after drying overnight.




You don't want to let the glue get too dry or it will cause you major problems. I'd suggest only applying glue 16 - 20 hours before you're ready to paint. I applied on Saturday afternoon and painted Sunday morning. The top two holes will not dry to the core, which causes a bit of mess, but trust me, its better than letting it dry all the way.

These things are the hardest piece to paint in my opinion. There are so many angles and sides to them and the gloss always has some spots thats are a little rough from overspray on an adjacent side.

But once I had all the paint applied I let it set for an hour and then began peeling off the masking . The two masking taped stripes came off easily, especially after I scored them with an exacto knife. The four bottom vertical channels were a little tougher to get. I scored each side of the channel a little on small side and pealed out the glue. It came out fairly easily leaving a just a little trace in each channel. The real hard part here was using an exacto knife to remove the excess paint along each ridge. You can tell wich direction the paint will want you to trim based on trial and error. Then its just taking it nice and easy along the perimeter of the channel. Mine came out ok, one channel messed up a little along one side but it almost looks like weathering chips so I was ok with it.



The top two deep cutouts went about the same way. I scored the paint with the exacto and pulled out the dry portion of the glue. Then I used paper towels and q-tips to remove the still wet glue at the bottom of each hole. There will be some mess here, but if you go slow it will be minimal. Once that was done I used the exacto to carefully cut the excess paint along the edge of the hole. A slow steady hand is definitely key.



Once I had removed all the masking, cleaning everything up as best I could, I did some light wet sanding on a few blemished areas of the covers, Then I rinsed the whole thing off and let it dry for about 15 minutes. Next I applied 2-3 more clear coats over the whole piece. I've found this helps cement the edges of the paint where the masked areas were. Without it the paint there would chip away pretty quick. I did the same thing on my coin slots. You can't even tell there's clear over the bare aluminum areas. The only reason I did 2-3 coast was because of the aforementioned inclination of these particular parts being hard to get an even clear coat on. One would be enough, if you can get it in one. Even with all that process the top of my cover has a bit of a rough patch in the clear coat. I'm not sure I'm going to be able to get it any better though. I may decide to rig up some sort of card board mask to help me shoot only the top with clear. One thing I've learned through all my painting is that it will never be perfect. These parts almost tell you where you're going to have to weather them. Once you do, these little imperfections will just add to the character.




Thursday, April 5, 2012

Artoo on the Side

Side Vents arrived today from Guy in Burbank, CA. These perfectly match the Pocket Vents he ran earlier this year. Painted portions of the Power Couplers this weekend. Still trying to figure out the best way to mask off the remaining ring around the center of the Couplers.



Sunday, March 25, 2012

Begin again

Spent part of the weekend on Artoo! I stripped the paint or primer, not sure what it was, off the outer half moon details I purchased off the junkyard. Still need to do the inner ones. One of these was banged up a little and some sanding took care of the majority of it. Also stripped the paint off the coin slots. The original paint job I did flaked too much when I was taking off the masking.

Painted the blue portion of Pocket Vents & Octagon Ports. I tried it a little differently this time after reading up about painting techniques on the forums. Only waited about 2 hours after the primer coat to lay down the rest instead of 24+. Then I removed the masking around 2-3 hours after the last clear coat was down. The masking came off easy on the Octagon Ports, the paint was only around 2 hours old. Waited a little longer on the Pocket Vents because I had to sand out some imperfections on the clear coat and hit them again. I noticed that the tape was about to pull the paint  so I scored it with an Xacto and it came off quite easy. 

I think the quicker process will solve a lot of my painting problems. I went back thorough all the blue I've painted and about half needs some sanding and touchup on the clear coat. The biggest hurdle will be getting the Booster Covers painted. Two tries already and neither was successful.


Friday, December 9, 2011

No Longer Feeling Blue

Not much on the blog front lately. I've mainly been getting all the blue paint as finished as I can before the cold weather finally set in a couple weeks ago. All but about 3-4 pieces will need some clear coat touchup next spring when the weather abides again.

Had some success with masking the Booster Covers with Elmer's Glue. The bottom four masked areas on each didn't turn out to well though. Masking Tape on the coin slots didn't fair very good as well. I posted a thread about masking tips on the forums, and the best advice I think I gathered from responses is that masking should be removed fairly quickly - within 2 hours. That way the paint is still pliable enough not to chip. Looks like these 3 parts will be stripped and attempted again this Spring with the remaining blue pieces I've yet to receive.

Not sure yet, but I'd like to attempt the Dome Lighting Kit sometime in the next couple months while its too dang cold to do much else.

I've ordered a few more parts, there's only a handfull left to go and most are electronics. The HP servo mounts came in yesterday. These allow a servo hookup to the HPs to add movement. Some assembly required.

Monday, October 31, 2011

Strip Searched

Couple of minor setbacks this week. First, after priming the Radar Eye with a couple coats of plastic primer, I went ahead and shot a coat of self etching on it. I only did this because I read it was still good for resin on the boards, and I wanted the same undercoat as all the other pieces so there wouldn't be any color variation. They were wrong. It cracked in several places and I had to do some major sanding to get it back into painting shape. My can of plastic primer sucked and the nozzle didn't work after the first round. So I used some clean metal primer on it. Its taken a few days to completely dry, but I think it just needs a little light sanding to smooth it and I can move ahead.

Thanks to someone else on the astromech.net boards, I tried clay as a masking agent in the booster covers. After over a week, the paint surrounding the clay still hadn't dried. I tried carefully to remove the clay, but it was pretty evident immediately that I would have to repaint. Acetone does a fairly good job of getting the paint off, at first it wasn't removing the primer. But I had to scrub a lot to gett all the paint off and the primer came off too in certain areas. I'll probably just give it a good sanding now and then reprime. One down one to go.



I tried rubber cement before the clay. It wasn't very exact, and shrank after drying. So I'll try good old masking tape this time around, it'll just be hard to get into the nook and crannies. I think I will spray the Radar Eye silver first, then mask off and spray the blue. Luckily weather here is showing in the 60s for the next week or so. Once all this painting is done I'll get started on the Dome Lighting Kit and getting the dome panels all cut out and hinged.

Sunday, October 23, 2011

Blue Period

Spent the last week painting a few blue pieces a night. Even had to get three more cans of the base blue. A couple pieces have some runs on them, so I'm going to sand everything down a little with some fine grit and re-coat the gloss. I tried it on one of the ankle detail pieces and it seemed to make it quite a bit smoother. I really like how it looks flat until you get it in the right angle of sunlight, then the metal flake pops and it looks a totally different shade of blue.

Sunday, October 16, 2011

Optimus Primed

Sanding and priming have taken longer than anticipated. Therefore I didn't get to the blue this weekend after all. A cold front is coming in this week, but it looks like it will warm back up by next weekend. Now I plan on a little light sanding of these pieces over the course of the week and then I'll blue them next Sunday.






Friday, October 7, 2011

Feeling Blue

I've been priming some of the blue parts I have over the past week. I plan on getting at least all the Dome pieces that need painting primed this weekend. There's a small chance of rain so not sure if I will actually get them all to final paint.

The so called "Krider Method" of painting is no longer quite the color I'm looking for since one of the colors in the formula is no longer available. Some people have substituted a different blue for the purple that was used in the original, but I'm not pleased with those results. Someone found what is called "Sonic Pearl Blue", which is the equivalent of Ford blue that is used on my Mustang. This was closer to what I was going for so I picked up a couple cans awhile back. A few people have been experimenting with using this as a base coat and the Anodized Blue from the Krider Method. I tried a couple different recipes and have come to a decision for what I'm going to use.



Although there is almost no discernable difference in the above photo, in person there is subtle variance. None of mine actually match the Ford as close as it looks. I guess human eyes are better than a 10 megapixel camera. I'm going with the far right method. Its a little more purple than the original Ford blue, but its the smoothest finish. In the right angle of sunlight it has a considerable amount metal flake.

So here are the cans if anyone out there wants to duplicate this method or try their own recipe. Primer and Gloss were from Home Depot/Lowes, and the Sonic Pearl Blue and Anodized Blue are from Advance Auto Parts.

Be sure and let the Primer dry 24 hours or so and wet sand any imperfections. Then only wait 15 minutes between all the coats of blues and gloss.